
Richer color and joints that stay full
Paver Sealing in Westchase, FL
Call (656) 254-4152 for a free paver sealing estimate at your Westchase driveway, pool deck or patio.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Can I get my Westchase pavers sealed, and how fast is the reply?
Paver sealing is available in every Westchase village, and a local contractor replies within 1 business day, usually much sooner. The estimate is free, and you are not obligated to book. To get started, call (656) 254-4152.
Sealing brings back deep color, keeps joint sand where it belongs and makes dirt rinse away more easily. Picture the drive you pull into after a long summer: gray at the edges, thin in the joints, then dark and even again. A driveway carries tires and oil drips, while a pool deck carries splash water and bare feet, so each area needs its own plan. Mention how each surface is used day to day when you request a free estimate.
Paver Sealing Westchase Is Proud to Serve Tampa Bay

What is included when pavers are sealed in Westchase?
Four things make up a sealing job: a walk-through, a deep clean, new joint sand and the sealer coat. Cleaning usually takes the longest, since sealer locks in whatever is left on the surface. To walk through each part as it applies to your house, call (656) 254-4152.
Walk-through
The contractor notes the size, low spots, cracked pavers, old sealer and any place water collects before naming a price.
Deep clean
Algae, mold, oil and rust each get a treatment that fits, followed by a careful rinse. Rusty's lists all four as part of prep.
Joint sand
Fresh sand packs each gap. Rusty's says it cuts down on weeds and ants and steadies the pavers over time.
Sealer coat
Sealer goes onto dry pavers at the rate on the label, by sprayer, roller or both.
How do I know my Westchase pavers need sealing?
Look for color that has gone flat or chalky, joints sitting below the paver edges, sand spread across the drive after a storm and green or black film in the shade. Rusty's names year-round UV, heavy summer rain and humidity as the main wear on Tampa Bay pavers. Topping up sand while the joints are shallow beats relaying pavers that have drifted. For a quick opinion, call (656) 254-4152.
Which sealer holds up in Westchase's humidity?
No single product suits every home, so ask which sealer the contractor plans to use and why. A Westchase paver company applies a water-based urethane as a flood coat followed by a finish coat, and Rusty's describes two coats of urethane in finishes from natural to high-gloss. To compare options for your pavers, call (656) 254-4152.
Unilock recommends water-based sealer when possible because tools clean up easily. It calls solvent-based sealer more durable but says it needs pavers and joints that are perfectly dry, and since solvent products evaporate faster, cooler weather suits them better. Ask which one is going onto your surface when you request a free estimate.
Wet look or natural finish: which fits my home?
A wet look deepens color and may add shine, while a natural finish stays close to the pavers' original look. Rusty's calls wet look the most requested finish in Tampa Bay, and Unilock warns that a high sheen can be slippery when wet. Beside a screened pool, footing counts for more than gloss. To see samples of both, request a free estimate.
How often should Westchase pavers be resealed?
Plan on every 3 to 5 years, the span Rusty's and Unilock both give. A driveway in full sun often needs attention near the 3 year mark, a covered patio can last 5 years or more and a pool deck wears faster because of chemicals and constant moisture. A Westchase paver company recommends 2 to 3 years, so expect the schedule to follow sun, shade and traffic. To have your coat checked, call (656) 254-4152.
Does a thicker layer of sealer protect pavers longer?
No. Unilock says to seal in one session and pass a dry roller over soaked pavers to take off the excess, because extra sealer leaves streaks, uneven gloss and a whitish film. One even coat at the rate on the label is the aim. If a bid pushes extra coats as extra protection, ask what the product label calls for before you request a free estimate.
When is the right time of year to seal pavers in Westchase?
Dry weather matters more than the date. Unilock asks for clear skies for 24 to 48 hours around the job, up to 48 hours of dry weather afterward and air between 50 and 90 degrees, with 75 ideal. Pavers that bake in direct sun can stain or peel ahead of schedule. To choose a day the weather allows, call (656) 254-4152.
Westchase gets its rain in a pattern. The wet season runs from late May to early October, with afternoon thunderstorms a regular event, so a summer job may slip a day or two. New pavers must wait, too. Unilock says 60 to 90 days, so efflorescence can clear first. If yours are newly laid, mention the install date when you request a free estimate.
Can sealing fix pavers that have sunk or shifted?
No. Unilock states that sealing is not a cure for poor drainage or subbase problems. Pavers that rock under a tire or hold a puddle need the base fixed first, since joint sand and sealer only hold on a stable surface. Rusty's makes the same point: sealing should protect a stable system, not hide an unstable one. Ask if leveling is in the price or billed apart when you request a free estimate.
Which areas of a Westchase home can be sealed?
A coat can go on a driveway, a screened pool deck, a patio or a front walk. Each one wears differently, so the plan shifts with the surface. To begin with the worst one, request a free estimate.
Driveways
Sealing a driveway matters most where the wheels run, since tires, oil drips and open sun all land there.
Screened pool decks and lanais
Sealing a pool deck means working around splash water, chlorine and bare feet, so the finish has to keep its grip when wet.
Patios beside a golf course or a lake
Backyards near a retention lake or a fairway stay damp longer. Sealing a patio there starts with the greenest corners.
Front walks and entries
Sealing a front walk is a small job, yet it is the first surface every guest steps on.
What causes paver trouble in Westchase?
Five problems show up again and again around Westchase: fading, lost joint sand, green growth, stains from oak and sprinkler water, and ground that has settled. Each is cheaper to deal with early. To see which of them touch your pavers, call (656) 254-4152.
1. Fading from year-round sun
Rusty's names constant UV as a main cause of fading on Tampa Bay pavers, and an open driveway with no shade loses its depth first. A fresh coat brings back color and slows the next round.
2. Joint sand lost in summer downpours
Heavy summer rain saturates pavers and erodes the sand between them, Rusty's explains. With the joints low, pavers can shift and weeds move in, so new sand goes in before any sealer.
3. Green growth in damp, shaded spots
Rusty's says humidity supports mold, mildew and algae, especially on pool decks, shaded patios and poorly drained areas. A Westchase paver company adds that wetlands, retention lakes, oaks and golf course irrigation keep many lots damp.
4. Stains from oak tannin and sprinkler water
Rusty's lists live oak tannin stains and hard water irrigation deposits as common local problems, and it notes that irrigation can leave rust marks too. Each needs its own treatment before sealer goes down.
5. Sandy ground that settles
Florida's state soil, Myakka fine sand, is sand throughout, and Wikipedia says its water table can sit within 10 inches of the surface for one to five months. Ground like that can settle under pavers, and Unilock says sealer will not cure a base problem, so low spots get fixed first.
What does paver sealing cost in Westchase?
Paver sealing in Westchase commonly runs $1.25 to $2.50 per square foot for the clean, sand and seal together, the range Rusty's Pressure Wash and Seal publishes for Tampa Bay. Price follows square footage first, then condition. Rusty's says prep, repairs, access, the sealer chosen and the material all move the number. For a figure written for your home, request a free estimate.
Size changes the rate. Rusty's says projects over 3,000 square feet may come in near $1.00 to $2.00 per square foot, while most companies set a minimum charge of $500 to $1,000, so a small patio costs more per foot than a big driveway. Material matters too: concrete is the most common and least costly, brick may need a clay-specific product and travertine can cost slightly more. Phone (656) 254-4152 to check a bid against these ranges.
A wash on its own is covered on the paver cleaning and joint sand page. Local coverage is on the service area list, and estimate requests start on the home page.
| Paved area | Typical example | Clean, sand and seal |
|---|---|---|
| 300 sq ft | Small patio or walkway | $375 to $750 |
| 600 sq ft | Two car driveway | $750 to $1,500 |
| 1,000 sq ft | Large driveway or pool deck | $1,250 to $2,500 |
| 1,500 sq ft | Driveway plus pool deck | $1,875 to $3,750 |
Math based on the $1.25 to $2.50 per square foot that Tampa Bay paver companies publish. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.

Why hire a contractor who works near Westchase?
A contractor who already works around Westchase plans for summer storms, shaded lots and lakeside dampness before arriving. Expect a written price before any work starts. To begin, call (656) 254-4152.
A contractor who works nearby
A company that covers Westchase already knows its villages, its lakes and its shady lots. The first visit starts from local knowledge, not guesses.
Free to ask
The look at your pavers and the written estimate cost nothing. If the number does not suit you, say no and nothing is owed.
Published prices to measure against
Tampa Bay paver companies post what they charge per square foot, and this site passes those figures along. A bid far outside them deserves a question about what it includes.
Your pace, your decision
Request the price in writing, then take as long as you need. The contractor standards page covers what to check before you sign.
Ready for a free paver sealing estimate in Westchase?
Call or send the short form, and a reply comes within 1 business day, often much sooner.
Free, no obligation

How do pavers look after sealing in Westchase?








How does the paver sealing process work from start to finish?
Most jobs follow five steps, from the first look to a final walk-through. To get on a schedule, call (656) 254-4152.
1. Walk it and measure
To price the sealing job at your Westchase home, the contractor measures the area and marks dips, cracked pavers, old sealer and any spot where water collects.
2. Cover and treat
Plants and screen panels are covered and the sprinkler timer is switched off. Mold and algae treatment, oil stain removal and rust treatment go on wherever they are needed, as Rusty's lists.
3. Wash with care
A rotary surface cleaner covers the pavers evenly, the way Rusty's describes, and any hose or wand spray stays at 30 degrees or lower, per Unilock, so the joints keep their sand.
4. Dry and refill the joints
Unilock says pavers dry in a few hours in warm sun and need about a day in cool shade. Fresh sand is then swept into each gap, which Rusty's says cuts down on weeds and ants.
5. Seal and walk the job
If sealer is on the work order, it goes on dry pavers with a garden-style sprayer and a foam or short pile roller, as Unilock lists. The contractor then walks the area with you and names how long feet and tires should stay off.
Frequently Asked Questions
What is the average cost to seal pavers in Florida?
In Tampa Bay, companies commonly publish $1.25 to $2.50 per square foot to clean, sand and seal, and Rusty's Pressure Wash and Seal gives that range. A 600 square foot Westchase driveway would land near $750 to $1,500. Repairs, leveling and stripping a failed old coat are usually extra.
How much does it cost to seal outdoor pavers?
Rusty's Pressure Wash and Seal lists about $500 to $1,000 for a 250 square foot patio, $1,000 to $2,000 for an 800 square foot pool deck and $1,250 to $2,500 for a 1,000 square foot driveway. It adds that most companies set a minimum charge of $500 to $1,000, so a small job costs more per foot.
What are the downsides of sealing pavers?
Sealing is a repeat expense, since Unilock says many owners reapply every three to five years. A high sheen finish can turn slippery when wet, and sealer is not a cure for poor drainage or a weak base. Over-application, or a product that clashes with an old coat, can leave a whitish film.
How often should pavers be resealed in Florida?
Rusty's says most surfaces need resealing every 3 to 5 years, with a sunny driveway closer to 3 and a covered patio up to 5 or more. Pool decks wear faster, and a saltwater pool can shorten the life of the coat compared with chlorine. A Westchase paver company puts the cycle at 2 to 3 years.
Is it better to spray or roll paver sealer?
Either works, and many contractors use both. Unilock lists a garden-style sprayer with an adjustable nozzle, a foam roller or a short pile roller. It suggests soaking the pavers, then passing a dry roller over them to lift extra sealer and prevent streaks and drips.
Do I need association approval before sealing pavers in Westchase?
Often not for a clear coat on existing pavers, according to a Westchase paver company, which still tells owners to check village guidelines first. A hardscape company adds that the community association reviews most exterior changes, so ask before you change a color or add a tint.
How long does it take to seal pavers at a Westchase home?
A Westchase paver company says most jobs run one to two days. After that, Rusty's says foot traffic is usually fine in about 24 hours, and driveways need 48 to 72 hours before cars return. Unilock asks for up to 48 hours of dry weather with the sprinklers off.
Can a Westchase pool deck be sealed without making it slippery?
Yes, if the finish is chosen with care. Unilock says high sheen gloss can turn slippery when wet, while a penetrating matte finish keeps more grip. A Westchase paver company says pool decks and walkways can take an anti-slip additive. Ask the contractor which finish goes beside your pool.
When should pavers be sealed around Westchase's rainy season?
Pick a dry stretch. Wikipedia puts the wet season in this part of Florida from late May to early October, with afternoon thunderstorms a regular event. Unilock wants clear skies for 24 to 48 hours around the job and air between 50 and 90 degrees, and Rusty's says spring, fall and winter often work well.
Ready to book a look at your Westchase pavers?
Phone in or send the short form, and a contractor answers within 1 business day, often well before that.
Free, no obligation
